Close

Results 1 to 10 of 10
  1. #1
    DF Jedi bulletproof's Avatar
    Join Date
    Apr 2002
    Location
    Lancashire
    Posts
    1,583
    Thanks
    93
    Thanked:        58
    Karma Level
    312

    Help help lost a pad on my liteon drive!!!

    please can someone help me...

    i was trying to bridge the points on my liteon drive so i could dump the key. its gone a bit wrong....

    one of the pads has come off and can no longer bridge the point...

    can anyone help me out, i can send the drive and pay the going rate, i also need someone to provide i drive to put the key onto it so i can use it. i will pay the going rate for that as well as p&P

    i have a hitachi 47d and a samsung m25 that could be used...

    please can someone help, really need to get this sorted...

    thanks alot

    BP

  2. #2
    DF VIP Member AD's Avatar
    Join Date
    Jan 2001
    Location
    Bolton, Uk
    Posts
    3,001
    Thanks
    747
    Thanked:        487
    Karma Level
    498

    Default Re: help lost a pad on my liteon drive!!!

    Bullet,

    All you have to do is get a piece of wire (Kynar) and put one end in the hole beneath the 2 pads you are bridging. If its the left pair you have lost, put the wire in the hole and solder the other end to the top pad near the Sata ports RxD. Connections.

    Or the right pads put the wire in the hole beneath and then solder the other end to the bottom TxD pad.


    -=AD=-

  3. #3
    DF Jedi bulletproof's Avatar
    Join Date
    Apr 2002
    Location
    Lancashire
    Posts
    1,583
    Thanks
    93
    Thanked:        58
    Karma Level
    312

    Default Re: help lost a pad on my liteon drive!!!

    hi mate

    thanks alot for the reply, not sure about putting wire through the hole, never done it before. if i was to mess that up i could be stuck with a knackered drive...

    i think i may need to find someone who could do it for me...

    Thanks alot

    bp

  4. #4
    DF Jedi tronads's Avatar
    Join Date
    Aug 2008
    Location
    Blackpool
    Posts
    2,473
    Thanks
    73
    Thanked:        235
    Karma Level
    296

    Default Re: help lost a pad on my liteon drive!!!

    Ill sort it for you if you like....anywhere near Blackpool / Preston ?

  5. #5
    DF PiMP wreksta's Avatar
    Join Date
    Apr 2002
    Location
    newcastle
    Posts
    390
    Thanks
    1
    Thanked:        0
    Karma Level
    234

    Default Re: help lost a pad on my liteon drive!!!

    i can also do mate if you want but its rrealy not that hard to do bit of keynar wire tip the end with solder and place in the hole it works a treat

  6. #6
    DF Jedi bulletproof's Avatar
    Join Date
    Apr 2002
    Location
    Lancashire
    Posts
    1,583
    Thanks
    93
    Thanked:        58
    Karma Level
    312

    Default Re: help lost a pad on my liteon drive!!!

    thanks alot guys for all the offers, vgopal has offered to help...

    thanks once again

    BP

  7. #7
    DF Jedi tronads's Avatar
    Join Date
    Aug 2008
    Location
    Blackpool
    Posts
    2,473
    Thanks
    73
    Thanked:        235
    Karma Level
    296

    Default Re: help lost a pad on my liteon drive!!!

    AD, just for info, the "left pair" do not need to be bridged, only the "right pair" is actualy required.

    Quote Originally Posted by AD View Post
    Bullet,

    All you have to do is get a piece of wire (Kynar) and put one end in the hole beneath the 2 pads you are bridging. If its the left pair you have lost, put the wire in the hole and solder the other end to the top pad near the Sata ports RxD. Connections.

    Or the right pads put the wire in the hole beneath and then solder the other end to the bottom TxD pad.


    -=AD=-

  8. #8
    DF VIP Member AD's Avatar
    Join Date
    Jan 2001
    Location
    Bolton, Uk
    Posts
    3,001
    Thanks
    747
    Thanked:        487
    Karma Level
    498

    Default Re: help lost a pad on my liteon drive!!!

    Quote Originally Posted by tronads View Post
    AD, just for info, the "left pair" do not need to be bridged, only the "right pair" is actualy required.

    Unless you want to go back in the drive when the firmware is finally released, I do both.

    -=AD=-

  9. #9
    DF Jedi tronads's Avatar
    Join Date
    Aug 2008
    Location
    Blackpool
    Posts
    2,473
    Thanks
    73
    Thanked:        235
    Karma Level
    296

    Default Re: help lost a pad on my liteon drive!!!

    I know the drive has been flashable for quite a while now (just there is nothing yet to flash to it), but I hadnt heard that the flash method was going to be through the serial interface....have you heard this is definitely going to be the case ? I might as well start bridging the other point again while im in there if thats the case I guess.

    I only made the point anyway because the OP was just concerned about getting his key, and therefore only needed to be advised on the minimum to get him fixed up.

  10. #10
    DF Jedi tronads's Avatar
    Join Date
    Aug 2008
    Location
    Blackpool
    Posts
    2,473
    Thanks
    73
    Thanked:        235
    Karma Level
    296

    Default Re: help lost a pad on my liteon drive!!!

    AD, you have probably read by now that c4e says the flashing is sata, and only the key extraction is serial. You can move to only working on one point now.....should save you about 10 seconds ;-)

Similar Threads

  1. [WANTED] Liteon 360 drive
    By matthewy2 in forum Buy, Sell and Trade
    Replies: 3
    Last Post: 28th January 2011, 09:37 PM
  2. liteon drive
    By Preddy in forum Microsoft Consoles
    Replies: 8
    Last Post: 12th May 2010, 11:44 AM
  3. Replies: 12
    Last Post: 24th December 2009, 12:00 PM
  4. liteon drive
    By ashleywalls in forum Microsoft Consoles
    Replies: 1
    Last Post: 22nd November 2008, 02:28 PM
  5. Replies: 22
    Last Post: 4th November 2003, 07:25 PM

Social Networking Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •