How to build your own SLIC 2.1 Bios

Thread: How to build your own SLIC 2.1 Bios

  1. Raptor's Avatar

    Raptor said:

    Default How to build your own SLIC 2.1 Bios

    1. Load your original motherboard bios


    2. Choose your SLIC File


    3. Choose your SLP File


    4. Choose and Verify with Certificate

    5. Press "GO" and wait till this "SLIC performed successfully"
    (do not press any keys, MMTOOL runs automatically)


    6. You can press "VERIFY" but all should be fine.

    7. now flash your "SLIC Bios".

    8. when finished reboot Win7 and start Everest, you should see now:


    All done. You´re now SLIC 2.1 ready

    Download Slic Tool v1.2
    [Only registered and activated users can see links. ]
     
  2. DejaVu's Avatar

    DejaVu said:

    Default Re: How to build your own SLIC 2.1 Bios

    Please ignore my ignorance, but what is this for exactly?

     
  3. frodo123456's Avatar

    frodo123456 said:

    Default Re: How to build your own SLIC 2.1 Bios

    if i'm not mistaken m8, it's for inserting the oem information into your motherboard bios. dell asus etc. no need to use loaders and cracks for vista or win 7 then. it will just automatically activate them.
     
  4. AD's Avatar

    AD said:

    Default Re: How to build your own SLIC 2.1 Bios

    Is there not one available for Award Bioses Rap?

    -=AD=-
     
  5. Tim.Lad's Avatar

    Tim.Lad said:

    Default Re: How to build your own SLIC 2.1 Bios

    Quote Originally Posted by AD View Post
    Is there not one available for Award Bioses Rap?

    -=AD=-
    Very active forum for all this here

    [Only registered and activated users can see links. ]

    And yes award bioses can be done..

    Acer EFI bioses cannot be done yet
     
  6. Raptor's Avatar

    Raptor said:

    Default Re: How to build your own SLIC 2.1 Bios

    [Only registered and activated users can see links. ]
     
  7. vgopal's Avatar

    vgopal said:

    Default Re: How to build your own SLIC 2.1 Bios

    i used this, flashed the bios, all hacktivated
     
  8. tiggerbiker's Avatar

    tiggerbiker said:

    Default Re: How to build your own SLIC 2.1 Bios

    Quote Originally Posted by Raptor View Post
    [Only registered and activated users can see links. ]
    found my slic bios on there - thanks

    not yet upgraded my 7100 build to the RTM build - no excuse now i suppose
     
  9. XBOX4LIFE's Avatar

    XBOX4LIFE said:

    Default Re: How to build your own SLIC 2.1 Bios

    I would if possible download your own bios from the source, just to be safe, some of the pre-made slic bios files have been found to contain malware

    [SHOWTOGROUPS="80"]
    AMI tool... [Only registered and activated users can see links. ]
    AWARD tool... [Only registered and activated users can see links. ]
    How to... [Only registered and activated users can see links. ]
    Tested ok [/SHOWTOGROUPS]
     
  10. sinbrad's Avatar

    sinbrad said:

    Default Re: How to build your own SLIC 2.1 Bios

    Can't seem to get the Slic Tool v1.2 from the above link and other places I've tried have all had the file removed? Any other places I could try?
     
  11. Anakin's Avatar

    Anakin said:

    Default Re: How to build your own SLIC 2.1 Bios

    Quote Originally Posted by sinbrad View Post
    Can't seem to get the Slic Tool v1.2 from the above link and other places I've tried have all had the file removed? Any other places I could try?
    [Only registered and activated users can see links. ]
     
  12. Jacko's Avatar

    Jacko said:

    Default Re: How to build your own SLIC 2.1 Bios

    i downloaded the amitool133 software, and downloaded my bios.rom file, but i cant find an Asus.bin (SLIC21) file. i have the slp and the certs. anyone help me find them? should they come with the amitool?
     
  13. Waka's Avatar

    Waka said:

    Default Re: How to build your own SLIC 2.1 Bios

    I've got a couple of the Windows 7 OEM disks (and haven't yet installed) - does this mean I need to frig the bios? I'm sure a couple of my mates have installed it on any old boxes and it seems to work for them?

    W.
     
  14. Jacko's Avatar

    Jacko said:

    Default Re: How to build your own SLIC 2.1 Bios

    well i cant manage to flash mine, i did the above etc.. when it comes to trying to flash the actuall asus bios using EZFlash i get the following error;

    "Boot Block in file not loaded"
     
  15. XBOX4LIFE's Avatar

    XBOX4LIFE said:

    Default Re: How to build your own SLIC 2.1 Bios

    I didn't use EZflash as I was told it might not flash (or dump) the whole bios, I use awdflash.exe for award bios files but never come across a ami to flash yet, giz 5 i'll have a look
    Had a look but i'll need more info on the motherboard to get the right flash.exe, I would look at the board manufacturers site for a bios flash program that works in dos, was the bios you modified taken from the board makers site or a mb bios dump ?
    Last edited by XBOX4LIFE; 6th November 2009 at 07:40 PM.
     
  16. XBOX4LIFE's Avatar

    XBOX4LIFE said:

    Default Re: How to build your own SLIC 2.1 Bios

    Yor using an old version of the amitool

    [SHOWTOGROUPS="80"]
    v1.41 - [Only registered and activated users can see links. ]
    [/SHOWTOGROUPS]
    found this which might in case it seriously fooks up
    Spoiler:

    AMI has an embedded recovery technique in the 'boot block' of the BIOS. In the event that the BIOS becomes corrupt the boot block can be used to restore the BIOS to a working state. The routine is called when the 'system block' of the BIOS is empty or corrupt. The restore routine when called will access the floppy drive (1.44Mb floppy disk drive) looking for a file named AMIBOOT.ROM.
    This is the reason the floppy drive light comes on and the drive appears to be in use. If the file (AMIBOOT.ROM) is found it is loaded into the 'system block' of the BIOS to replace the corrupted information.
    To restore your BIOS copy the most recent version of your motherboards BIOS file to a floppy diskette and rename it AMIBOOT.ROM. The diskette does not need to be bootable or contain a flash utility. It will access the floppy from 2-5 minutes the system will beep four times. Remove the floppy diskette from the drive and reboot the computer. if when you turn on the system it does not try to access the floppy, press and hold the 'CTRL' and 'HOME' keys at the same time. This will force the system (assuming the 'boot block' isn't corrupted) to access the flopy and look for the AMIBOOT.ROM file.
    Note: 12345678.BIN represents the name of your BIOS.
    Step by Step:

    1. Rename the desired AMI BIOS file to AMIBOOT.ROM and save it on a blank floppy disk. e.g. Rename 12345678.ROM to AMIBOOT.ROM


    2. Insert this floppy disk in the floppy drive. Turn On the system
    3. If no floppy access occurs press and hold Ctrl-Home to force update. Follow insructions on the screen and it will read the AMIBOOT.ROM file and recover the BIOS from the A drive.


    4. When 4 beeps are heard you may remove the floppy disk.


    5. Restart the computer.






    Sorry bout the funky peach fellaz, it wouldn't fork off
    Last edited by XBOX4LIFE; 6th November 2009 at 07:55 PM.
     
  17. Jacko's Avatar

    Jacko said:

    Default Re: How to build your own SLIC 2.1 Bios

    Quote Originally Posted by XBOX4LIFE View Post
    Yor using an old version of the amitool

    Sorry bout the funky peach fellaz, it wouldn't fork off
    [/spoiler]

    haha.

    manage to flash it using the EzFlash program and i grabbed a pre done slip file.

    now im running fully registered OEM windows 7 ultimate.

    only problem now is its an old flash file and not the newest.

    if i was to re-flash the bios with the latest firmware would this remove the 2,1 table?
     
  18. Raptor's Avatar

    Raptor said:

    Default Re: How to build your own SLIC 2.1 Bios

    yes m8
     
  19. mfield's Avatar

    mfield said:

    Default Re: How to build your own SLIC 2.1 Bios

    I'm trying to do this on a Toshiba. I have downloaded the the original bios and the modified bios and I have AMI Slic 1.41.

    I am a little confused as what to do next as in the manufacturer list there is no Toshiba? Any help would be great!
     
  20. mfield's Avatar

    mfield said:

    Default Re: How to build your own SLIC 2.1 Bios

    Got sorted lads, just downloaded the modded bios from
    [Only registered and activated users can see links. ]
    I then downloaded the original bios from Toshiba, replaced the original with modded bios and flashed.

    Then I got one of the OEM codes off the above site, went and activated and BINGO - we're laughing!