Close

Results 1 to 10 of 10
  1. #1
    DF Rookie sherman1's Avatar
    Join Date
    Aug 2002
    Location
    UK
    Posts
    10
    Thanks
    0
    Thanked:        0
    Karma Level
    0

    Default X-ecuter botched install

    Hi, I installed an x-ecuter today but it does't work. I'm using the alternative wire solder point on the bottom of the motherboard but when I boot, the led flashes red and green. I re-soldered the lpc points but it still repeated the same thing. I didn't tin the points before, could this be the cause? I definitely didn't splash any solder on the board. If I disable the mod, it still plays originals fine. Any idea what I can do guys?
    Thanks:o:

  2. #2
    DF Rookie BeerBarron's Avatar
    Join Date
    May 2002
    Location
    Australia
    Posts
    7
    Thanks
    0
    Thanked:        0
    Karma Level
    0

    Default

    Did you solder the point at the screw hole? I installed one the other day, it looked sweeet but didnt work. The reason being I had missed that solder point.

    Just a thought!!!

  3. #3
    DF Rookie sherman1's Avatar
    Join Date
    Aug 2002
    Location
    UK
    Posts
    10
    Thanks
    0
    Thanked:        0
    Karma Level
    0

    Default

    Thanks but yea I installed that..

    I think I might have to take my chip out and put it back in, how am I meant to take it out?? It seems like you can't

  4. #4
    DF Rookie BeerBarron's Avatar
    Join Date
    May 2002
    Location
    Australia
    Posts
    7
    Thanks
    0
    Thanked:        0
    Karma Level
    0

    Default

    It is hard to get it off but not impossible. The way I took mine off was to lift a corner (be a little forceful) and unsolder the points from closest to that corner out. If that makes sense. Just keep applying heat and eventually it will come off.

    Hope that helps ya!

    l8r

  5. #5
    DF Member Prodigal's Avatar
    Join Date
    Jan 2001
    Location
    Durban, South
    Posts
    29
    Thanks
    0
    Thanked:        0
    Karma Level
    0

    Default

    It's easy to take the x-ecutor out. Get yourself a solder pump/sucker. Heat up the connection points, and suck off the solder. I have managed to remove x-ecutors in a matter of seconds like this. Also, before attempting to remove it, have you tested that each of your solder points are making contact? Simply prop the MB on it's side (lean it on the heat sink) and use a DMM to test for continuity between the solder points on the mod and the solder points on the other side of the MB. They might look like they are connected, but that doesn't always mean they are.
    Last edited by Prodigal; 8th September 2002 at 12:38 PM.

  6. #6
    DF Member oka97's Avatar
    Join Date
    Jan 2001
    Location
    England, London
    Posts
    25
    Thanks
    0
    Thanked:        0
    Karma Level
    0
    haha never mind Sherman..

    Looks like I'm going to have to clean up your botched install

  7. #7
    DF PiMP DoctorX's Avatar
    Join Date
    Jan 2001
    Location
    USA
    Posts
    333
    Thanks
    0
    Thanked:        0
    Karma Level
    224

    Default

    I had the red and green flashing and checked all points and now it is green and orange any ideas?

  8. #8
    DF Member Prodigal's Avatar
    Join Date
    Jan 2001
    Location
    Durban, South
    Posts
    29
    Thanks
    0
    Thanked:        0
    Karma Level
    0

    Default

    Originally posted by DoctorX
    now it is green and orange any ideas?
    Plug your A/V cable into the back of the XBox.

  9. #9
    DF Founder Raptor's Avatar
    Join Date
    Nov 1999
    Location
    USA
    Posts
    93,405
    Thanks
    462
    Thanked:        1,834
    Karma Level
    5531

    Default

    Originally posted by Prodigal


    Plug your A/V cable into the back of the XBox.
    lol yeah

  10. #10
    DF PiMP DoctorX's Avatar
    Join Date
    Jan 2001
    Location
    USA
    Posts
    333
    Thanks
    0
    Thanked:        0
    Karma Level
    224

    Default

    well I feel real stupid

    Xbox works now and plays originals - now I just need to find some media which it reads

    any suggestions for someone in the US

Similar Threads

  1. VWallpaper botched iPhone
    By ashtech in forum Apple Mobile Devices
    Replies: 14
    Last Post: 7th September 2010, 11:14 PM
  2. Colostomy reversal botched, suit says
    By BertRoot in forum News & Current Affairs
    Replies: 0
    Last Post: 1st December 2007, 12:04 PM
  3. Botched Operation Left Him `Gay`
    By Tattooed Freak in forum The Dog and Duck
    Replies: 21
    Last Post: 17th February 2004, 02:15 AM
  4. anybody supply & install x-ecuter v1.1 in hull !
    By logicman88 in forum Microsoft Consoles
    Replies: 0
    Last Post: 3rd November 2002, 08:20 PM
  5. X-ecuter install problems!
    By Neilt in forum Microsoft Consoles
    Replies: 7
    Last Post: 17th October 2002, 09:33 AM

Social Networking Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •