Can ya help i have a dti1000 and ligbdebug config wont set the id on the box it says error comms ive kept trying but still nout olz help!!
Can ya help i have a dti1000 and ligbdebug config wont set the id on the box it says error comms ive kept trying but still nout olz help!!
Hi,
Com'on people help this lad no replies in ages.
Anyway i have spoken to this person on msn and i have tried to help him.. then i clicked something channelman told me a few month back.. anyway he bought a unhacked 2000 box off me he couldnt set the net id... the battery was flat..
as a last resort i think this may be the problem.. without actually seeing it.. because this box has been offline 2+ years so yeah i think it wont set net id cause its dead???
Anyone have any ideas??
Well m8, that was the prob with the box I bought off you.
NetID set OK in Libby.....read OK in Libby.......but when
checked in Eng Menu after a quick power-down it was back
to 09999. I new battery sorted it out.
Coms error does sound different though....means box is
not talking to Libby. Check it's on Com1 and that the
cable is OK. Try cable on something else like a Phoenix/
Smartmouse. Make sure you have the correct config file
for a 1000 box loaded into Libby.
Try these and let us know how you got on.
Channelman
Hi channelman well m8 i can do lots of things with this cable in liby but a cannot change network id m8 it just says comms fail m8 have you got a config for the 1000 m8 so i can just try?
Here's the Libby config file suitable for 1000 boxes.
You'll need to edit the netID for your own area.
Channelman
Thx m8 tried it still didnt work does the battery charge up again m8?
Could be that the box is stuck in the loop.. you did say ur software was wrong on the box?? am i right in thinking you mean cr2??
get a test sim the box sound's like it's pre cr soft so changing net-id in libby won't work.
or flash the atmel's.
don't ask on here for dump's either.
have aread
HOW TO USE LIBBY
Follow the steps below and all should be ok.
1. Turn on pc and get the box somewhere near you but NOT plugged in at all.
2. Open Libdebug (Libby) and load the correct config (cfg) file for your box making sure that the config file is pre programmed with the correct net id for your area.
3. Plug the lead from your pc into the rs232 socket of the box, this will be a scart lead if your box is a 4000. DO NOT APPLY POWER TO BOX YET.
4. Now click "Execute command" in the libby window.
5. Quickly apply power to the cable box. After a few seconds you should see a load of data appear in the bottom right window of Libby.
6. Look in the top left (white) window of libby and scroll down to NET ID, click the + sign to the left of it and then look for your area.
7. Double click on your area and some data will appear in the top right window of libby, double click the area again.
8. At this point you could reset the pin on your box if you do not know it, just double click "clear sram" in the top left window of libby.
9. Exit Libby and plug in the cable feed e.t.c and go straight to engineers menu to check that NET ID has changed. Whilst there you should enter a new pin if you cleared sram. If the net id is not the one required Just run through the process again as sometimes you need to do it twice.
HOW TO EDIT A LIBBY CONFIG FILE
If you need to edit Libby with the correct NET I.D for your area then here's how to do it.
1. Download the correct config (cfg) file for your model of box.
2. Right click on the downloaded file and select "open with" then click notepad.
3. Scroll down the opened file until you see:
:Network ID
Set Network ID
4061*****
Set Network ID
4061*****
4. The * represent the net id so just delete the last 5 digits and replace them with your own NET I.D.
5. Click FILE in the top left corner and select "save as"
6. In the filename box call the file whatever you like but make sure that you add .cfg to the end of the filename so it might look like 2000.cfg
wambo, i'm afraid you wasted your time as far as this guy is concerned, look at his posts, he signed up, got what he wanted then fu*ked off.
THIS IS WHY WE IMPLEMENTED THE 10 POSTS RULE.
anyway i'm giving you some karma for helping out as no doubt someone else will find it helpfull
cheers abcman ref: df admin ..............as i said in my into duction got a lot to offer when i can get online....im afraid my first ten posts or 20 were just to say hi to every one to get into the forum..... but as you can see with the few posts that i have answered to all helpful info......i have not took any thing out and fooo:censored oooked offhere to help when i can.......................................:thumbs :thumbs
Social Networking Bookmarks