Close

Results 1 to 5 of 5
  1. #1
    DF MaSter coogy's Avatar
    Join Date
    May 2002
    Location
    Blackburn Lancs
    Posts
    97
    Thanks
    0
    Thanked:        0
    Karma Level
    0

    Default Prassi PrimoDVD Options Problem

    I'm using Prassi PrimoDVD v2.0 Build 2.0.749 on WinXP Pro Service pack 1. No problems burning discs, that's fine, but when I try to go into options I get the following: - "Run-time error '9' subscript out of range" then when you click ok the program shuts down. Has anyone encountered this problem and if so what's the solution. Thanx in advance

  2. #2
    DF VIP Member Pegasus's Avatar
    Join Date
    Jan 2002
    Location
    Hampshire
    Posts
    4,588
    Thanks
    13
    Thanked:        52
    Karma Level
    619

    Default

    I've had exactly the same problem and it was caused by flashing my 40x LiteOn to a 48x.
    Disconnect all your recording devices from the IDE bus and plug them back in one at a time while trying to get to the options screen, when it falls over then you have found the device causing the problem.
    Make sure you switch your system off before attempting to disconnect or re-connect your devices!!
    Understeer is when you hit a wall with the front of your car
    Oversteer is when you hit the wall with the back of your car
    Horsepower is how fast your car hits the wall
    Torque is how far your car sends the wall across the field once you've hit it

  3. #3
    DF MaSter coogy's Avatar
    Join Date
    May 2002
    Location
    Blackburn Lancs
    Posts
    97
    Thanks
    0
    Thanked:        0
    Karma Level
    0

    Default

    I also have a Liteon 40x although I haven't flashed it to a 48x. Didn't know you could. Could this drive be causing the problem, it's supposed to be supported

  4. #4
    DF MaSter coogy's Avatar
    Join Date
    May 2002
    Location
    Blackburn Lancs
    Posts
    97
    Thanks
    0
    Thanked:        0
    Karma Level
    0

    Default

    It was the Liteon drive causing the problem. I disabled it in device manager and the options now work. There's nothing I wanna change in there anyway now I've seen em! Guess I'll just enable drive again and never bother looking at options again! Thanx for your help Pegasus, much appreciated.

  5. #5
    DF VIP Member Pegasus's Avatar
    Join Date
    Jan 2002
    Location
    Hampshire
    Posts
    4,588
    Thanks
    13
    Thanked:        52
    Karma Level
    619

    Default

    No problem
    Understeer is when you hit a wall with the front of your car
    Oversteer is when you hit the wall with the back of your car
    Horsepower is how fast your car hits the wall
    Torque is how far your car sends the wall across the field once you've hit it

Similar Threads

  1. prassi primo HELP
    By raven282 in forum PC Software
    Replies: 3
    Last Post: 16th January 2003, 04:06 PM
  2. Blending Options problem in Photoshop 7.0
    By BAQUAN in forum PC Software
    Replies: 1
    Last Post: 21st October 2002, 11:03 AM
  3. Replies: 1
    Last Post: 26th September 2002, 01:09 AM
  4. Prassi PrimoDVD 2.0 problem with Philips dvdrw228
    By DarkManx2x in forum PC Software
    Replies: 1
    Last Post: 19th September 2002, 03:51 PM
  5. Prassi PrimoDVD 2.0 (English)ps2 dvd+r
    By DarkManx2x in forum Sony Consoles
    Replies: 2
    Last Post: 19th September 2002, 02:16 PM

Social Networking Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •