RGH noob help....

[macmilm]

Plan on gettin stuff to finally RGH one of me consoles in next couple of weeks.... have done a bit of readin but thought I would get some input from the DF'ers...

Am I correct in thinking all I need is a coolrunner kit ???!?!?!?!

TBH I dont plan on doing it myself.. gonna try find someone who wont spunk solder all over the inside of my XBOX as would happen if I did it. Dont have steady hands and fingers are like cumberland sausages

Do I also need to get a nand-x ?!?!?!?

Thanks for any advice.


I think some of the tuts I have looked at are out of date so thought I would ask

[ethanhawk]

Your gonna need a nandx m8.

[tronads]

You will need a one-time use of a nand-x (ie you could borrow one) and a coolrunner which remains in the console.

[macmilm]

So coolrunner + nand-x = RGH !!!!

I have a phat.. ( i think Jasper HDMI)

Thanks guys

[DejaVu]

Without hijacking the thread too much, someone's meant to have done mine over the past few weeks, but reckons he's having problems doing it because it's a Zephyr and has now reset it back to stock. The Coolrunner is soldered in and he's going to leave it in. It's now updated to LT v3.0 instead. It's a 2009 Elite IIRC.

Any truth to that or is he just being rubbish? Can I still get someone with more experience to sort the RGH?
Apparently it worked 1 in 4 boots, but after a while stopped booting all together.

[ethanhawk]

Seems to be a bit hit and miss .
Try here :-- http://team-xecuter.com/forums/showt...ghlight=zephyr

[BIG-TED]

dejavu would have thought that would have been a falcon, the zephyr can be a pita.

Macmilm, if its a slim, instead of nand x go for jr programmer, then you can feck about with the on/eject sounds too, also what dash are you on might need dgx when its released depending on current dash version.

Ted

[macmilm]

dejavu would have thought that would have been a falcon, the zephyr can be a pita.

Macmilm, if its a slim, instead of nand x go for jr programmer, then you can feck about with the on/eject sounds too, also what dash are you on might need dgx when its released depending on current dash version.

Ted

Its a phat m8 !!!

[macmilm]

Turns out its a Falcon not a Jasper as previously thought but from what I have read its only Xenon's that are a problem.. right?

[ethanhawk]

Thought they wasn't many problems with falcon . Here's the link to tut.

If u need to borrow a nandx I have one here .
Drop me a pm if u need it

[macmilm]

Thought they wasn't many problems with falcon . Here's the link to tut.

If u need to borrow a nandx I have one here .
Drop me a pm if u need it

Appreciate the offer mate...not gonna attempt this myself tho... awfull at soldering.. hopin to find someone to do it (hint hint) - cash waiting lol
Main problem at the mo is finding a coolrunner in stock.. everywhere says out of stock.. have found one but suspect it is not genuine xecuter!!!
Am i best to avoid the rip off coolrunners due to quality e.t.c

Thanks for advice all

[ethanhawk]

Have always brought the real xecuter products , so can't say anything bout fake stuff. We're are u based ?

[macmilm]

Suffolk / East Anglia mate..
Think I have managed to find one that claims to have CR3 Lite in stock (ukmodchips.com)
I assume it would be genuine from them but never used em b4.

Do I need to get a QSB aswell ?

[ethanhawk]

The QSB makes it easier but I just used wires.
Am in luton so bit far for me.
If u get stuck , I can do for cost of p&p.